{"id":999,"date":"2026-09-08T08:26:09","date_gmt":"2026-09-08T08:26:09","guid":{"rendered":"https:\/\/isbmmolding.com\/?p=999"},"modified":"2026-09-08T08:56:22","modified_gmt":"2026-09-08T08:56:22","slug":"what-are-the-three-types-of-blow-molding","status":"publish","type":"post","link":"https:\/\/isbmmolding.com\/sv\/what-are-the-three-types-of-blow-molding\/","title":{"rendered":"Vilka tre typer av formbl\u00e5sning finns det?"},"content":{"rendered":"

Vilka tre typer av formbl\u00e5sning finns det?<\/h1>\n
\n

There are three main types of blow moulding: extrusion blow moulding (EBM), injection blow moulding (IBM), and injection stretch blow moulding (ISBM). Each forms its plastic intermediate differently, producing containers with different performance characteristics, dimensional accuracy, and resin compatibility. The right type depends entirely on the container you need to produce.<\/p>\n

Type 1 \u2014 Extrusion Blow Moulding (EBM)<\/h2>\n

A continuous extruder pushes molten plastic through a die, forming a hollow tube called a parison. The mould closes around the parison, pinches the bottom, and blow air inflates it against the mould walls. EBM is used for HDPE containers, automotive fuel tanks, industrial drums, and any large container where an injection-moulded preform would be impractical. It does not produce biaxial molecular orientation and is not used for PET.<\/p>\n

Type 2 \u2014 Injection Blow Moulding (IBM)<\/h2>\n

Plastic is injection-moulded around a core rod at station one, forming a precise preform with the finished neck thread already formed. The core rod transfers the preform to the blow station, where air pressure inflates it. No stretch rod is used, so no axial orientation is produced. IBM is the standard process for small pharmaceutical vials, dropper bottles, and HDPE personal care containers where neck precision matters most.<\/p>\n

\"IBM<\/p>\n

IBM operating principle \u2014 preform injection around a core rod, then air inflation at the blow station; no stretch rod, no biaxial orientation.<\/p>\n

Type 3 \u2014 Injection Stretch Blow Moulding (ISBM)<\/h2>\n

ISBM adds a mechanical stretch rod to the blow station. Before high-pressure air expands the preform radially, the stretch rod extends it axially to 2.5\u20133.5 times its injection length. The simultaneous axial stretch and radial blow produce biaxial molecular orientation \u2014 the defining feature that gives ISBM containers their glass-like clarity, light weight, and structural strength. ISBM is the process of choice for PET water bottles, CSD bottles, pharmaceutical oral dose containers, cosmetic PETG flacons, and edible oil containers.<\/p>\n

\"Products<\/p>\n

Container range from ISBM \u2014 from 30\u00a0ml pharmaceutical vials to 10-litre edible oil containers, all produced with biaxial molecular orientation.<\/p>\n

Side-by-Side Comparison<\/h2>\n\n\n\n\n\n\n\n\n\n\n
Attribut<\/th>\nEBM<\/th>\nIBM<\/th>\nISBM<\/th>\n<\/tr>\n<\/thead>\n
Mellanliggande<\/td>\nExtruded parison<\/td>\nInjected preform on core rod<\/td>\nInjected preform on mandrel<\/td>\n<\/tr>\n
Stretch rod<\/td>\nNo<\/td>\nNo<\/td>\nYes<\/td>\n<\/tr>\n
Orientation<\/td>\nIngen<\/td>\nIngen<\/td>\nBiaxiell<\/td>\n<\/tr>\n
Typiska hartser<\/td>\nHDPE, PP, LDPE<\/td>\nHDPE, PP, PC<\/td>\nPET, PP, PETG, PC<\/td>\n<\/tr>\n
Size range<\/td>\nSmall to very large<\/td>\n5\u2013500 ml<\/td>\n30 ml\u201310 L<\/td>\n<\/tr>\n
Clarity<\/td>\nLow<\/td>\nM\u00e5ttlig<\/td>\nGlass-clear (>90%)<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n

Need to identify the right blow moulding process for your container?<\/p>\n

Ever-Power supplies both IBM and one-step ISBM machines. Send your container specification and we will confirm the right process and machine model within 24 hours.<\/p>\n

Diskutera din ans\u00f6kan<\/a><\/p>\n<\/div>\n

Explore the full one-step ISBM machine range<\/a>eller recension anpassade formalternativ<\/a> for your bottle format.<\/p>\n

Vanliga fr\u00e5gor<\/h2>\n
\nWhich type is best for PET water bottles?<\/summary>\n
\n

ISBM is the correct process for PET water bottles at all volumes. Biaxial orientation gives PET water bottles their glass-like clarity, light weight (8\u201310\u00a0g for 500\u00a0ml), and structural strength. EBM cannot process PET economically, and IBM produces unoriented PET with insufficient clarity for beverage applications.<\/p>\n<\/div>\n<\/details>\n

\nIs ISBM the same as stretch blow moulding (SBM)?<\/summary>\n
\n

The terms overlap. SBM or RSBM typically refers to two-step reheat stretch blow moulding, where preforms made separately are later reheated and blown. ISBM specifically refers to the one-step integrated process. Both produce biaxially oriented containers; the difference is whether the preform is made in the same machine (ISBM) or a separate machine (RSBM).<\/p>\n<\/div>\n<\/details>\n

\nCan one machine perform all three types of blow moulding?<\/summary>\n
\n

No. EBM, IBM, and ISBM are mechanically distinct processes requiring purpose-built machines. An EBM machine uses a continuous extruder; an IBM machine uses a core rod rotating table; an ISBM machine uses a mandrel rotating table with a stretch rod at the blow station. The three cannot be combined in a single machine platform.<\/p>\n<\/div>\n<\/details>\n

Resin Compatibility: How Each Type Handles Different Materials<\/h2>\n

EBM works best with resins that extrude as a continuous melt without sagging \u2014 HDPE, LDPE, and PP, whose long molecular chains provide the melt strength needed to support a hanging parison. PET is almost never processed by EBM because its narrow orientation temperature window makes parison extrusion impractical at commercial production rates. IBM processes HDPE and PP predominantly; the core rod limits IBM to relatively short, wide containers because the core rod becomes structurally compromised at high L\/D ratios. ISBM, by contrast, uses a separate mandrel for preform transfer \u2014 not a core rod remaining in contact during blowing \u2014 which allows it to handle a much wider range of preform geometries including tall, slender pharmaceutical bottles.<\/p>\n

Capital Cost Comparison Across the Three Types<\/h2>\n

Machine capital cost varies significantly across the three types at equivalent output capacity. EBM machines for small HDPE containers are typically the least expensive entry point, often available at USD 20,000\u201380,000. IBM machines for pharmaceutical vials range from USD 30,000\u2013120,000. One-step ISBM machines start at approximately USD 50,000 for compact 3-station models and range to USD 350,000 and above for large-format 4-station servo-hydraulic machines. All three types require additional investment in matched moulds and process ancillaries (compressor, chiller, dryer) beyond the machine price. When comparing total investment across types, include tooling and ancillaries in the comparison \u2014 a lower machine price may be offset by higher tooling cost or more complex ancillary requirements.<\/p>\n

Application Decision Framework<\/h2>\n

A practical decision framework for selecting among the three types of blow moulding: if the container is HDPE, large (above 5 litres), or has an integral handle, start with EBM. If it is a small pharmaceutical vial or HDPE dropper bottle where neck precision is paramount, start with IBM. If the container is PET, requires high clarity or light weight, or will be filled with a liquid product (water, beverage, oil, pharmaceutical liquid), start with ISBM. If in doubt, specify the container\u2019s resin, volume, neck finish, required clarity, and fill temperature to an application engineer at Ever-Power \u2014 these five parameters almost always resolve the process selection question unambiguously and without additional cost or delay.<\/p>\n

The Historical Development of Blow Moulding Types<\/h2>\n

Understanding how the three types of blow moulding developed historically helps clarify why each occupies its current application niche. Extrusion blow moulding (EBM) is the oldest commercial blow moulding process, developed in the 1940s and 1950s primarily for HDPE milk jugs and household chemical containers. Its simplicity \u2014 extrude a parison, clamp the mould, blow air, eject \u2014 made it the first viable high-volume process for hollow plastic containers. Injection blow moulding (IBM) was developed in the 1960s and 1970s as a solution for pharmaceutical containers where EBM\u2019s neck finish precision was inadequate and the base pinch seam created contamination concerns. ISBM was developed in the 1970s and 1980s, initially to serve the emerging PET carbonated soft drink bottle market where EBM was impractical with PET and IBM could not achieve the required light weight and CO\u2082 barrier performance.<\/p>\n

Each process was developed because the existing processes were unable to serve a specific combination of container requirements. This historical context is useful because it confirms that the three processes are genuinely complementary rather than competitive \u2014 each occupies a specific application space defined by the combination of container size, resin, dimensional precision, and performance that it uniquely serves.<\/p>\n

One-Step vs Two-Step within ISBM<\/h2>\n

Within the ISBM category itself, there is a further distinction between one-step and two-step processing. One-step ISBM, which is what Ever-Power\u2019s EP-HGY and EP-BPET machines perform, integrates injection and blow in the same machine and the same thermal cycle \u2014 the preform is never cooled to room temperature between injection and blowing. Two-step ISBM (reheat stretch blow moulding, RSBM) separates the injection and blow steps into different machines: preforms are injection-moulded, cooled, stored, and later reheated and blown in a dedicated blow moulder. Two-step processes dominate at very high volumes (major water and CSD brands) where the decoupling of injection and blow cycles enables very high blow moulding throughput; one-step dominates at mid-volumes and in applications where the single thermal cycle reduces contamination risk or enables more complex preform geometries.<\/p>\n

Hur man startar leverant\u00f6rsutv\u00e4rderingsprocessen<\/h2>\n

F\u00f6r k\u00f6pare som \u00e4r nya inom upphandling av ISBM-utrustning kan processen att v\u00e4lja en maskin- och formleverant\u00f6r verka skr\u00e4mmande. Den praktiska utg\u00e5ngspunkten \u00e4r inte en lista \u00f6ver leverant\u00f6rer utan en tydlig beh\u00e5llarspecifikation: definiera flaskvolym, halsfinish, harts, m\u00e5lvikt, \u00f6nskad effekt och eventuella applikationsspecifika krav (farmaceutisk GMP, varmfyllning, renrumskompatibilitet) innan du kontaktar n\u00e5gon leverant\u00f6r. Med en komplett beh\u00e5llarspecifikation i handen kan du f\u00e5 meningsfulla och j\u00e4mf\u00f6rbara offerter fr\u00e5n flera leverant\u00f6rer, eftersom varje offert kommer att baseras p\u00e5 samma tekniska indata.<\/p>\n

Ever-Powers f\u00f6rhandsbed\u00f6mning b\u00f6rjar med en teknisk granskning av kundens containerspecifikation. V\u00e5rt applikationsteknikteam bed\u00f6mer specifikationen mot v\u00e5rt maskinsortiment, rekommenderar l\u00e4mplig modell (antal stationer, kl\u00e4mkraft, drivsystem) och tillhandah\u00e5ller en prelimin\u00e4r bed\u00f6mning av formgenomf\u00f6rbarheten \u2013 allt utan kostnad och vanligtvis inom 24\u201348 timmar efter att ha mottagit specifikationen. Denna prelimin\u00e4ra bed\u00f6mning g\u00f6r det m\u00f6jligt f\u00f6r k\u00f6pare att f\u00f6rst\u00e5 den troliga maskin- och formkonfigurationen, och den tillh\u00f6rande investeringen, innan de binder sig till en detaljerad offertprocess.<\/p>\n

Ever-Powers kompletta ISBM-produktsortiment<\/h2>\n

Ever-Powers kompletta sortiment av enstegs ISBM-maskiner t\u00e4cker alla st\u00f6rre till\u00e4mpningar inom l\u00e4kemedels-, kosmetika-, livsmedels-, dryckes- och industriell beh\u00e5llareproduktion:<\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Modell<\/th>\nStationer<\/th>\nKl\u00e4mma (kN)<\/th>\nBeh\u00e5llarintervall<\/th>\nK\u00f6ra<\/th>\n<\/tr>\n<\/thead>\n
EP-HGY50-V3-EV<\/td>\n3<\/td>\n50<\/td>\n30\u2013500 ml<\/td>\nFull servo<\/td>\n<\/tr>\n
EP-HGY150-V4<\/td>\n4<\/td>\n150<\/td>\n100 ml\u20132 l<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-HGY150-V4-EV<\/td>\n4<\/td>\n150<\/td>\n100 ml\u20132 l<\/td>\nFull servo<\/td>\n<\/tr>\n
EP-HGY200-V4<\/td>\n4<\/td>\n200<\/td>\n200 ml\u20133 l<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-HGY200-V4-B<\/td>\n4<\/td>\n200<\/td>\n200 ml\u20133 l (handtag)<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-HGY250-V4<\/td>\n4<\/td>\n250<\/td>\n500 ml\u20135 l<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-HGYS280-V6<\/td>\n6<\/td>\n280<\/td>\nKomplexa former<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-HGY650-V4<\/td>\n4<\/td>\n400<\/td>\n2\u201310 liter<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-BPET-70V4<\/td>\n4<\/td>\n200<\/td>\n500 ml\u20133 l (PET)<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-BPET-94V3<\/td>\n3<\/td>\n250<\/td>\n1\u20135 liter (PET)<\/td>\nServohydraulisk<\/td>\n<\/tr>\n
EP-BPET-125V4<\/td>\n4<\/td>\n400<\/td>\n5\u201310 liter (PET)<\/td>\nServohydraulisk<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

F\u00f6r fullst\u00e4ndiga tekniska specifikationer f\u00f6r varje modell, bes\u00f6k Produktsidor f\u00f6r EP-HGY och EP-BPET<\/a>F\u00f6r applikationsspecifik v\u00e4gledning, kontakta v\u00e5rt team p\u00e5 isbmmolding.com\/kontakta-oss<\/a> eller mejla sales@isbmmolding.com. Vi svarar inom 24 timmar p\u00e5 alla tekniska fr\u00e5gor.<\/p>\n

One-Step vs Two-Step ISBM: A Fourth Consideration<\/h2>\n

Within the ISBM category itself, there is a further distinction between one-step and two-step (reheat) ISBM. One-step ISBM \u2014 the process used by Ever-Power\u2019s EP-HGY and EP-BPET series \u2014 performs injection, conditioning, stretch, and blow in a single integrated machine. The preform goes from resin pellets to finished bottle without ever leaving the machine or losing its initial thermal energy.<\/p>\n

Two-step ISBM, also called reheat stretch blow moulding (RSBM), separates the process into two distinct machines. A preform injection moulding machine produces preforms that are cooled, stored, and then conveyed to a separate reheat blow moulding machine where they are reheated and blown. Two-step is the dominant technology for very high-volume commodity beverage production \u2014 large CSD and water bottling plants \u2014 because it allows very high output rates by decoupling the injection and blow cycle times. One-step is preferred for pharmaceutical, cosmetic, food, and mid-volume beverage applications because it eliminates preform storage and handling, reduces contamination risk, and requires a simpler capital structure.<\/p>\n

Selecting the Right Type for Your Application<\/h2>\n

The most common buyer error when specifying blow moulding equipment is selecting a machine type based on familiarity or price rather than application fit. A buyer who processes HDPE for household cleaning product bottles may be accustomed to EBM, but switching to PET cosmetic flacons requires a completely different machine type \u2014 ISBM \u2014 with different mould tooling, different resin handling, and different process parameters. Similarly, a pharmaceutical producer who has used IBM for small HDPE dropper bottles and wants to move to 1-litre PET bottles for oral nutritional supplements needs to understand that IBM does not produce the biaxial orientation or clarity that PET requires in that application \u2014 the correct machine is an ISBM.<\/p>\n

The rule of thumb: if the container is PET or PETG and requires clarity, light weight, and structural strength, the process is ISBM. If the container is small HDPE or PP and requires neck precision without orientation, the process is IBM. If the container is large, uses a handle, or is made from HDPE at high volume, the process is EBM.<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"

What are the three types of blow molding? There are three main types of blow moulding: extrusion blow moulding (EBM), injection blow moulding (IBM), and injection stretch blow moulding (ISBM). Each forms its plastic intermediate differently, producing containers with different performance characteristics, dimensional accuracy, and resin compatibility. The right type depends entirely on the container […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[1],"tags":[],"class_list":["post-999","post","type-post","status-publish","format-standard","hentry","category-product-catalog"],"_links":{"self":[{"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/posts\/999","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/comments?post=999"}],"version-history":[{"count":4,"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/posts\/999\/revisions"}],"predecessor-version":[{"id":1011,"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/posts\/999\/revisions\/1011"}],"wp:attachment":[{"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/media?parent=999"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/categories?post=999"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/isbmmolding.com\/sv\/wp-json\/wp\/v2\/tags?post=999"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}